|
Shortstop
#1 Trailer Concrete Mixer Detailed Specifications
|
|
|
Mfg:
|
Ernest Industries, Inc.
|
|
|
Model:
|
Shortstop #1
|
|
|
General:
|
Self contained one cubic yard capacity rotating drum concrete mixer and trailer.
The unit is designed to mix concrete, grout, masonry, and refractory products.
The Shortstop #1 features a Honda 11 HP gasoline engine, planetary reduced
hydraulic powered drum and drum tilt cylinder. The drum is equipped with
aggressive helix fins and paddles to thoroughly mix all types of materials.
The drum tilts to discharge material to forms, buggies, wheelbarrows and more.
The Shortstop features simple to operate controls including drum direction,
speed, and tilt. The unit is mounted 5,999# double axle trailer frame complete
with hydraulic surge brakes and adjustable height coupler. The Shortstop #1
requires a tow vehicle with a minimum 6000# towing capacity.
|
|
|
Dimensions:
|
| |
Length:
| 14' 10" |
| |
Width:
| 5' 6" |
| |
Height:
| 6' 7" |
| |
Empty Weight:
| Approximately 2,000 lbs. |
| |
Loaded Weight:
| Approximately 5,999 lbs |
|
|
|
Drum:
|
36" diameter spun head with 10 gauge high strength steel rolled to form the
conical drum. The drum is fully welded inside and out. One each access panel
is provided for access to interior of drum with the approximate dimensions of
22" X 26" oval. A heavy-duty steel track ring fully welded on the rear drum
section is provided.
|
|
|
Agitation:
|
Three each 180 degree helix mixing/discharge fins with wash holes located
approximately 12" on center. Two each paddle mixer fins located in forward
cone fabricated from 10 gauge high strength steel and rigidly welded to 1"
round bar and reinforced rear.
|
|
|
Drum Rollers:
|
Two each heavy-duty drum rollers with cast iron wheel, re-greasable bearings and
dirt seals shall be provided. The grease fittings for the rollers shall be
assessable from the rear of the mixer without removal of sheet metal guards.
Each roller is equipped with a sheet metal cover to guard pinch points.
|
|
|
Drive:
|
The planetary features the Ernest Industries exclusive gimbal mounted design
to allow the drive to move freely with the drum. The drive is hub mounted with
8 each 1/2-13 grade 8 bolts for easy service and features a 5:1 gear reduced
planetary drive. The hydraulic motor is directly coupled to the planetary
drive with a spline shaft. Case drain oil from the hydraulic motor lubricates
the planetary, thus no special gear oil or lubrication for drive unit is required.
|
|
|
Controls:
|
Conveniently located on the driver's side rear is the control panel. The
controls consist of directional drum control (agitate, neutral, discharge),
drum speed and drum tilt. The controls are simple to operate and feature
operational and safety decals.
|
|
|
Engine:
|
Honda 11 HP gasoline engine, with recoil start with 50 state EPA approved
emissions. Engine shall be complete with on/off switch, factory installed
fuel tank and keyed output shaft.
|
|
|
Hydraulic Pump:
|
Directly coupled to the Honda engine / gear type hydraulic pump.
|
|
|
Hydraulic Reservoir:
|
Fabricated from 1/4" carbon steel complete with filler/strainer/breather,
return filter, inlet strainer, valve, sight gauge and baffle. The reservoir
has a capacity of approximately 10 US gallons. Hydraulic hoses
feature JIC type fittings, (no pipe fittings) and all hoses are secured
in vibration proof clamps.
|
|
|
Frame:
|
The mixer frame is fabricated from 2" X 4" X 1/4" grade A500 structural steel
tubing, electrically welded at all joints. The frame is specifically designed
for the stresses imposed by agitating ready mixed concrete. Joints are rigidly
reinforced with gussets and all tubes are capped and fully welded.
|
|
|
Axles:
|
Two each 3,500# axles with leaf type springs are provided. Each
axle features a grease fitting on the hub for lubrication.
|
|
|
Wheels:
|
White spoke five lug wheels.
|
|
|
Tires:
|
Goodyear ST225/75-15
|
|
|
Fenders:
|
Heavy-duty 14 gauge bolt on fender are provided. The fenders are powder coated
to resist chips and dings.
|
|
|
Brakes:
|
Four wheel hydraulic surge brakes with free reverse.
|
|
|
Hitch:
|
Adjustable height hitch, simple turn the adjusting handle and the hitch can
be adjusted to level the load and for alternate hitch heights. The Shortstop
#1 comes standard with a 2-5/16" ball type hitch; but a pinnel type hitch is
available. The hitch assembly is complete with safety chains and surge
brake safety disconnect cable.
|
|
|
Lighting:
|
Combination (stop/turn/tail) lights are provided on the rear of unit. A
license plate holder with light and fender mounted amber clearance lights
are provided in accordance with DOT regulations.
|
|
|
Finish:
|
The complete mixer will be covered with one coat of enamel primer and two
finish coats of enamel paint. The standard colors are frame black or gray
and white mixer drum.
|
|
|
Parts & Service:
|
Ernest Industries carries a complete inventory of parts available for immediate shipment within 24 hours.
|
|
|
Warranty:
|
Mixer carries a one year warranty against defective parts and workmanship.
See attached "terms of sale & warranty" for detailed information.
|
|
|
Operators Manual:
|
One complete operators manual will be supplied with the unit. Serious injury
or death could result from the improper use or misuse of the mixer. Questions
concerning the operation of Shortstop Mixers can be addressed by calling
(937) 325-9851 or email sales@ernestindustries.com.
|
|
|
Tow Vehicle:
|
Requires a tow vehicle with a minimum 6,000 lb towing capacity. Verify tow vehicle capacity before operation.
|
|
| Optional Equipment |
